Reviewing Free Energy Generators. A Response to My Video "Nikola Tesla's Greatest Invention"- 102

Several months ago I posted a

video

about Nikola Tesla's

invention

of the induction motor. If you haven't seen that

video

, it will be helpful if you watched it at the beginning, but it won't be necessary because I'll show you the important segment. Here, just a minute after the video was posted, I got a huge influx of emails and comments from people asking me about all these different

free

energy

devices they're seeing on YouTube, which ones are real and which ones are fake. Know? Did Nikola Tesla invent a device? which was suppressed by the government after

reviewing

a bunch of these videos, I decided that instead of going through them one by one and trying to tell you what works and what doesn't, I decided to answer two really key questions, the first.

The question is why would anyone bother making a fake video about

free

energy

? And second, how can I know if a device is real or not? And those are the questions we want to answer today. There are a couple of concepts about how engines work that I want to answer. make sure we're on the same page and I've covered this in great detail in that Nikola Tesla video that I featured. There's a three-minute segment that's really important, very important, in fact, I'll show it to you here again. Even if you've seen that video, I ask you to watch the next three minutes to make sure we have the exact same information in our heads before moving on to the next part where I explain how to differentiate between what works and what doesn't pass foreign electricity through a cable?

There is a magnetic field produced around the wire, in fact that magnetic field has a north pole and a south pole to demonstrate this. I'm going to use this compass that I have here on my work table. North is directly. behind me and this wire is currently connected to a circuit that is off, if I turn on the power and apply some voltage you will see the compass needle start to rotate to align with the magnetic field of the wire, that is because of that magnet. It's much closer than the Earth's magnetic field when I turn off the power, it goes back to the Earth's magnetic field and gets even better, although if you take the wire and wind it all in the same direction the strength of the magnetic field increases. and if you take a piece of iron and push it in the middle, that also increases the magnetic field to illustrate how it works.

I took this transformer out of the microwave literally a few minutes ago. What's important to us is that it's one piece. iron with two coils of wire inside, the one on this side is much more wrapped than the one on this one, so we're going to use this one and if we put electricity in it we should be able to turn this thing into a magnet. so right now it's not magnetic but we put power on it and now let's start passing some current through it okay that's definitely pulling it now and let's put some more on it yeah okay we have an electromagnet , so now we should be pretty.

We are comfortable with the idea that if we pass electricity through a wire, we will get a magnetic field around the wire and that magnetic field becomes stronger if we knock on the wire, this also works the other way around, if we move a magnet over a wire, get electricity, let me show you this is just a stack of ceramic magnets and as you can see when I bring it close to the coil I'm starting to read a voltage on my multimeter and that's because the electricity is actually starting to flow through this top. Coil here, if I move it a little faster and a little closer, I actually get higher voltages, which means more electricity flows, but there's one more thing you need to know before we get away from this: if the magnet is still , there is no voltage.

There is relative motion between the magnet and the coil of wire, as long as I'm inputting some motion, I'll get a voltage there. Pop Quiz I hope you were paying attention because here we go, in the last clip I said that the voltage reading indicated that electricity was flowing through the meter, but where is the power coming from? a comes from the multimeter B comes from the magnet obviously C comes from the atmosphere obviously D comes from my waving hand obviously why are you thinking about that first question I'm going to ask the second question. This is a question I get about once a month on my website and it usually goes something like this.

Well I don't know, electric cars like the Tesla have an alternator for those of you. who does not know the alternator of your gasoline engine car recharges the battery while driving, so the gasoline engine turns the alternator, the alternator puts electricity into your batteries and that allows you to start your car, the logic is as follows Yes If you have an electric car you can connect an alternator to the engine and then the output of the alternator goes to the batteries and you have an infinite loop of power while you drive you charge the batteries the batteries power the car and therefore you never need to plug in your car, we're going to go over this idea in a moment here on my workbench.

I have two DC motors with permanent magnets, as you saw in the illustration, before electricity can produce magnetism and magnetism can produce electricity that works at the level of the motor as well, if you rotate the shaft in a magnet DC motor permanent, it will behave like a generator and I can demonstrate it to you by simply connecting this motor to this motor and so you know there is no trigger activated here. I'll try to keep all these cables on the workbench. I literally have the input of this motor connected to the input of this motor and if I spin the shaft you can see that this motor behaves like a generator sending a small amount of electricity through these wires in this motor and it's like this motor being plugged in makes the shaft move this works in the other direction and as you can see, this can behave like a generator, this can behave like a generator, but this is where things started to get interesting Why can't I just connect this output to this output and so let's see here?

Oh, quite convenient. I have a rubber band there. What happens if I do this and spin this motor? What should happen? get electricity from here that runs to here what makes that spin what makes that spin what gives me electricity and I have an infinite power of perpetual loop right here on my workbench I want to see what happens there is a missing element we need some way After doing so the system started correctly as if it was obviously not doing anything now, but according to the logic we just showed, this should work forever. In the last video I watched on this topic, they actually wrapped a cable around the pulley of one of the motors and pulled it like they were.

He started the gas lawnmower and then allegedly turned on the system and it ran in the video. I'll give you some examples of how you can fake something like that here in a moment, even with continuous shooting, it's actually very easy to fake that. It brings me to the first question I mentioned: why would anyone bother setting all this up and pretending to produce power when they don't actually produce power? In the video, they usually claim that it is some kind of government cover-up and that they are trying to share this secret device with the world, so here's a deal.

Whenever there is an opportunity to make money, there will be scammers. They make these videos because people click on them out of curiosity and that's all they need. It's like the ultimate scam. I don't have to convince you to give me money personally or give me your bank account information. I just need you to click on the thumbnail and watch for a while and I earn money. It's beautiful when you get to the end of the video. You don't have to believe anything you just saw and this is why I don't show you any clips from those videos because, number one, if I explain to you how one guy did it, the next guy is just going to pretend. it's a little bit better and number two, I'll put a link in the description to tell you where I got the clip from and then you'll go watch it, which means they're going to make money off of me and my video.

I don't want those Rascals to do anything with me so I'm just not going to do it. Here is the problem with this setup and also the problem with the alternator example. If I pull this pulley now I have a pretty terrible problem. connection here, but you can see that they are actually spinning fine, in fact let me make sure they are not fighting each other because I don't want anyone to say yes, so the way the

generators

are set up now they spin in the same direction. it should be perpetual, okay let's try it again, it doesn't work, it just doesn't work, it's very easy to prove to yourself that it just doesn't work, all you need to try, these are two little hobby DC motors, heck. you can get them out of your kids broken toys, they will have permanent magnet DC motors in them, a pair of two shafts together, connect the wires, you will have exactly this setup, in fact you will have a more efficient setup because you will connect them with actually , a belt is not the best way to transmit power.

There is a loss of power in the belt. The belt will move. The heat is building. Friction builds up when the belt slides just a little bit and that's all wasted energy. This is why when I built my dynamometer, it is designed to carefully measure horsepower accurately at the shaft. I couple the axles directly. I'm mainly just using a rubber band to poke fun at the idea that you can get power from a system like this whenever you design any mechanical system that uses belts or even gears, there will be some power loss in that drive no matter how it's configured , the belts may slip a little, there will be friction and heat and that's all part of the power leaking out of the system.

You also can't get more energy out of the system than you put back in, so even if the system were perfectly perpetual and 100% efficient, which is impossible, then it would be autonomous, but it wouldn't be possible to plug something else into the system because If you have bled even a small amount of power, the system should stop. All normal motors on the market have some type of inefficiency. In fact, most motors will tell you right on the label what the efficiency is. In fact, I'll put some labels on the screen. here for you and as you can see there is an efficiency rating that tells you how much energy is lost by running this motor now just to be clear if you have an efficiency of let's say 80 percent that means if your motor is drawing 100 watts from the wall, then only 80 watts of power come out of the shaft. 20 percent of that power is lost due to thermal friction in the bearings.

Things like that, electrical losses, there are a lot of little places where you just lose some power, so if we spin this shaft. and only 80 percent of that goes out and goes back to this engine and then this engine is also inefficient, so now only 80 of that 80 percent goes back out and then you just have some losses again, what will happen is with just one rotation, that cycle ends, you don't have enough power to keep the system running, you certainly can't connect something else to the system. Another misconception we see in some of these free energy videos is the idea that magnets can be used to work with other magnets.

Any video that shows one set of permanent magnets pushing another set of permanent magnets around perpetually is being faked, there is an external source supplying power to the system, there has to be and this is obvious to everyone. What you have to do is play with magnets. When you try to push them together, there is a repelling force there, but you notice that when I stop pushing them right now I am supplying energy. When I stopped the magnets, they stop if I turn them over and align the poles, they stick together but always come to a stable state.

The same thing will happen when you rotate two sets of magnets close to each other, they will lock and reach a stable state no matter how much energy you input. At first, any additional energy comes only from what you put into the system. Once the magnets are strong enough to overcome that input energy, it stops, so it's best to think of magnets as being more like a spring. I can use these magnets and there is potential energy when I push and force them so that potential energy can be released in the same way that potential energy can be released from a spring.

Now some physicists who have their PhD in magnetism are going to give me trouble with this, but I think this is a pretty good analogy to say that the potential energy is stored when I squeeze these two together and when you let go of them you can get energy from that, but the original energy source came from my hand even when one of these magnets is an electromagnet in that In case the external energy source is the power plant, it is not free energy, the energy is produced somewhere and not It's the atmosphere, it comes from a measurable source that is exhaustible, so let's revisit this idea of ​​putting a car alternator in an electric car that we just learned about.

Doesa few minutes, no generator is perfect, there will always be some power loss, meaning your car's alternator will need to draw 100 watts of power to generate 80 watts of power into the battery, using our example above. It doesn't take into account the energy used to drive the car, that's a completely separate thing: your electric motor not only generates enough energy to drive the car, it also draws enough additional energy from the battery to run the alternator, for example. what we can ignore. Turn on the electric motor for a moment and just say the alternator is running out of battery and what you get is the battery is losing 100 watts and gaining 80 watts back and you can see very quickly that we've wasted a lot of energy and that's why the manufacturers Car manufacturers don't put them in cars because you are literally wasting extra energy.

There is no benefit to having it there in one of these videos where they claim the power comes from magnets which actually take apart the alternator, this particular version has been copied many times, but they take apart the alternator, cut the wiring inside the rotor and then epoxy over neodymium magnets. First of all, you just made a terrible generator, it is much less powerful. Now that a few minutes ago before you cut the wires, now that you have permanent magnets there, they are not distributed evenly enough, the rotor itself needs to be very well balanced to be able to spin at a high speed.

Speed ​​machines can do this very easily, but in these videos the guy sticks these magnets on manually, which is just ridiculous. I think this is crazy and in my opinion I don't think you can spin an alternator like that when you see this later. In the video, they just put a different alternator in there and ran the same wiring on the outside, but even if you manage to balance it enough to not shake the whole thing to death, it certainly won't produce any more power. That part is just ridiculous. What I want to talk about now is how you can fake something like this because that's actually one of the things I want you to pay attention to in that video. what i was talking about with a ridiculous amount of views, they took a power strip like this, hooked up an alternator to one end of the system and then plugged the motor into the other end of the system and supposedly the alternator was powering the power strip and then a power strip ran the engine, the engine was connected to the alternator and so you had a perpetual system so I have a power strip very similar to the one in that video and let's tie this thing up so it doesn't move around while I'm plugging and unplugging things .

I need you to talk to us for a second, so the basic idea is that you connect your motor to this. Your alternator is connected here so the power that comes in through your alternator will power the strip and then the strip powers the engine, they are connected together so I have an extension cord here. I'm going to plug this in right here and plug it into the wall, okay, and here we have our light bulb, but there's actually another option that you see. From connecting a power tool or something else, which is what they seem to be doing in a lot of these demo videos, we could connect something else to this scenario, for example, okay, I'm offline, but I can make an extension.

The cable that looks like this has two male lenses, as you can see here, it's all the same cable. I'm going to plug it in and try not to let you be left with two wires sticking out. Yes, that is a danger. You should be careful or when you try to make a lot of money on YouTube you take a risk okay so plug this in oh what do you know? That works too so it took me less than a minute to make that extension cord and if you have three. or four things plugged into this and the cords are left at the bottom everywhere, as I've seen in many of these videos, there's no reason one of those extension cords couldn't just be a double ended extension cord that gives you allow In this case, turn on your alternator or your electric motor, which will make the entire system appear to be working in reality.

This powers your power tools, as well as running the motor and spinning the entire system. There are also other ways to fake this, e.g. I could make it look like the cable isn't there, so now you don't see the cable and there wasn't any jump cuts there, as you just noticed, the only thing that happened is that I split the screen and recorded some time with that. cable disconnected, that's all that's needed now. I didn't spend a lot of time working on this, but I can promise you that any of you can do this with a five-minute tutorial in Adobe Premiere from a YouTube video every time you see one of those clips where you say, "Oh, you know , this was all in one take and we didn't have any tricks here.

All you have to do is watch someone like Captain Disillusionment to learn the incredible number of ways people can manipulate footage to make it look like something is. ". happening in real time with no cuts when you're actually looking at two cuts right now, there's another slightly more challenging but certainly doable way to manipulate this and that is I can gut one of these and put a smaller motor inside of it and then I have A direct or belt drive system coupled within the motor itself that will rotate the fan and blades on the outside. The small motor inside can be powered by a battery and can make the system spin for several minutes at a time.

Remember they can cut this footage and try it again and again as many times as necessary, so let's say one time they accidentally exposed the wire that you weren't supposed to see, I mean, film it again, all you have to do is try and try until you nail it all at once and then you have it, you release your video and you get millions of views now that I've said all that, there are a few things I want to make very clear, number one, I don't pretend to know. all the possible ways to generate energy, there are definitely some things we haven't figured out yet, but this isn't it, this is rubbish and I wish these people would stop doing it, but as long as there is a way to make money from it, this people We will continue to make these videos, in fact the idea of ​​perpetual emotion goes back thousands of years, so we are by no means the last generation to deal with this problem.

This will continue as long as man is fascinated with the ways of getting down. cost or free energy now there are forms of free energy that we can use today such as solar energy there are advantages there which really is another form of solar energy if you think about it I certainly think you will make good use of your time discovering ways to capitalize it. things like solar and wind energy, but don't waste your time on this garbage, there are some things they try to do to give themselves more validity, for example, they hide their face and then cover it up saying something like oh, you know, me.

I don't want the government to come after me because it's a government cover-up which is ridiculous Claim either way, it won't take much for the FBI to find out who is producing videos on a particular YouTube channel, I don't mean to imply that I don't think their government cover-ups, of course there are, I mean there's everything from the Watergate scandal to On and On, they certainly are government cover-ups, but this isn't one of them, sorry. I'm laughing so hard because I'm thinking about the media right now. There's a clip in one of his videos where he talks about free energy where he gets up and just hits the camera.

There is no free energy device. Oh yeah, I love that guy. Another thing they will say very often is that it is not free energy, the energy comes from the magnets, but as I demonstrated before, you can put energy into the system and store it as potential energy, which is the demonstration I showed before, very similar to Springs . but the spring by itself is not going to do any work and the permanent magnet by itself is not going to do any work that is false thanks for watching foreigners foreigners