BEST way to TINT a Tesla Model 3 with Ceramic Tint (FULL ANALYSIS) | Houston, TX

What's wrong with everyone? This is Carlos at the Texas squeegee and um, okay, behind me I have the Tesla Model 3. Now this car has glass everywhere on the top. I mean, the entire roof might as well be a sheet. Now, a chubby guy like me after crashing two cars. In the car, you might as well call me crispy bacon because it's so hot in there. Now what we are going to do to solve this problem is to put

ceramic

can in the car, because that is what will keep the Heat the

best

, however, the purpose of this video is to show you how the

best

tip shop will handle the dyeing of one of the most difficult cards that gives problems to so many stores on the market, so stay tuned because you are about to see. a Texas Tech master or it doesn't shoot well, so one of the first things I'll do beforehand is test the performance before it has any

ceramic

tint

and then go back and see how much difference it makes.

So, I pulled out my handy heat lamp along with my dad's handy meter. Now, I turn this thing on, I'll let it sit here on the joint part so it can rest right there, once it has a position or something like that. meter there and right now it's reading about four hundred so this is without any advice we'll go back to ceramics to re-measure this thing and then see how much difference it really makes so okay one of the big ones. things before starting a car, especially with this one because of the sensitive electronics, in fact, which is so technologically advanced, this is a pre-preparation, so this is what we do because in these rear windows you lean a lot to reach the centers, so anything.

What you have here may scratch it, but having this prevents that from happening now. This here is to protect the switches and stuff that you have here, especially on the driver's side because this driver's side lock has a lot of other switches that control like the rest of the windows, so it's important to keep it dry. This car also has a speaker here, where we mask it and so the overspray doesn't get wet. Now, another important thing. I bought these windows when you close the door they go up so you're not supposed to roll down the windows when they have new

tint

.

So how can you avoid that? Well, I'll show you a trick. Get something like this. I mean, this is just my sword, but you can reach like a push stick and it reaches the latch right here. What you're going to do is push this in and spit this window out because it's going to think. that their doors closed so you see it here and now look at that window for the second click look now you think the door is closed now the reason you want to do that is in these bottom joints right here every time there's some kind of tint Peeling is because there is a joint that lifts it up, so if the film is cut below that joint and even at its highest point it never goes over it, it is never going to peel, we will do that to the four doors when this is impossible. one that gives so many people problems with this one we're not going to do this on two sheets and we're not going to do just half, we're going to do the whole thing on one

full

sheet of film, so that's going to be an interesting one, now that everything has been reduced, as you saw, the window goes from here to here, so this is the largest glass I think is on any civilian car that people struggle with.

A lot of it is because the bubbles were the finger bubbles that you have to shrink until they are up, maybe like a foot, maybe a little less than a foot, which is a lot of film to shrink, that's what causes the problem as I have been doing it. This went on for a long time and even I had them, I mean it wasn't too much, it wasn't that bad actually, but you know this takes some patience so one of the ways I'm going to prepare for this bottom piece right here . is using these microfiber rope gears from Soap Shield and that will prevent all the water that runs from here to the sides from getting into any possible electronic devices back here, okay, now that that's done, I'm going to show you a secret. weapon of how we keep everything protected and dry here so this is so social the robots telling you about this is what traps all the water and look how much water is actually there right now so look now others came with water due to such a big storm. rear glass when you clean it the water has to go somewhere so you don't want it to go places where it can damage things, this is where you want it to go and this is why we use Scioscia to protect all the electronics.

With these Teslas we would never have problems, so now that the cars are complete before we take them out, we are going to measure the performance of the ceramic and then compare it to the previous one, so I'm going to put that line right there where it is and then this is a meter and you see, we are now in the double digits, so now that the car is finished, let me take you for a little ride to see what we did. Now the side windows we are a completely computer cut tint shop so the side windows we did with our computer cutting system all we did was just shrink them and install them one of the key differences we made with this one we didn't You do it with other cars, it's the way we squeeze the water out of you, we go from side to side, unlike what you know, the side end ends at the bottom, it's not the part we avoid, the reason is because when The water goes down, the water runs into the door panels, so when you squeeze them outside, the water comes out and then goes straight to the floor, so if there's any chance of messing this up here, we completely avoid it. .

Now the unique things about these cars are these rear windows these are the windows that I see 10 shops struggling with all the time or people make them in two pieces which would mean you make them in one here and then the second one here no It looks great because you could I see the seam on the inside or I've seen the worst thing is when people just do it from here down and leave this part unattended. You can see it from the inside, it just doesn't look very good, so this is the right way to do it, which is a

full

sheet, it's complete, it doesn't look bad, it looks very, very good, it's the best way to do it and one key thing too, if you notice here, see that there is absolutely no humidity and what is that like? the water ran down here, how is it possible that we don't have moisture there?

And now you know it's a social robe that prevents that from happening, that's how we make windshields too, now this one has 30% surrounded. 30% is not that. dark, it looks dark because it has a black interior, so dark black interiors make movies look darker and that's pretty much what we did to this one, so now you just saw what it's like to see the best dye shop do the best job. with the best tint on the Tesla Model 3 now if you have one or if you have a car you want us to do visit us on our website at Texas Tech masters com subscribe to this channel to see the best tint videos from the best advice channel on youtube this It's Carlos from Texas squeegee checking in and see you next time