Maneira Fácil de Limpar Bico Injetor e Fazer Limpador de Bico Injetor, Caseiro! Faça Você Mesmo!

Hello guys, welcome to another video on the Cine Moto channel with you, in this video I am going to show you how to clean the injector nozzle with a 12 volt source And then 12 volts and this cleaning Guys, you can even do it even at home beauty Remembering that it works for any injection nozzle like I said guys I'm going to do this cleaning using a small 12 volt tip I'm going to do a demonstration Conca 80 and also with kerosene guys It's just a personal one however, here it is DC beauty and The nozzle only pulses with AC when I plug it in here guys, just give it a little touch, it's like it's on the battery And then it doesn't pulse So it's also good for you, you can't leave it direct because it will heat up and burn the coil of the injector nozzle and it will also remind you that the injector nozzle does not run on 12 volts, okay?

It works maybe three times something like that. It has a 12 volt input but it does not have a negative 12 volt. It is as if they took 12 positive volts from the battery and took another alternating current from another cable as if it were, say, the headlight, but it is much weaker than what it comes with. beauty mode, it will be published in the same way, well, for us to do this, guys, it doesn't hurt anything. Well, I'll show you here how to do this system to pull the injector. nozzle, it works very simple and I took this 12 volt source because it is easier to find, right? 12 volts, then it is used in scales and wifi antennas of how many other things that you can't find like this you can also get them. a 9 volt router will work you can even get 24 volts the way I'm going to do it here it will work great to do this little tip for cleaning the injector nozzle guys we're going to use a mini relay and then your reference.

Oh, it's here, up to 30 volts you can find this guy in MercadoLivre electronics stores, right, look for a 5-pin mini relay, you can't find a mini relay, you can also use it is an automotive 5-pin relay. Beauty will give the same effect. The first thing we're going to do here, guys, is make the relay use it by pulling on the nozzle. It will also work. Beauty, let's cut the power cord here, because there is another question from you about the nozzle connector. Now I will be. showing it to you And remember that this photo has positive and negative but in this system here guys it will not matter And then G1 we will do it in the following way, right, it is here so you can understand it, here is one pole of the relay coil and here is the other pole of the coil, this one in the middle, guys, with this other one here, it forms the closed contact.

Well, then what are we going to do? Any of them here, whether positive or negative, right, positive, here it has a little white band, it doesn't matter which one it is and what it is so that you guys can easily understand here guys, I can put any of these movies here, whether it is positive or negative , right in the contact closed in this Hello for him and this other one here guys. I can put it on any side of the coil, it can be this side or this side. Another thing is that it will work the same way, okay guys. , this way, now I'm going to do the welding here and here I am, the nozzle still doesn't come into the air, guys, here to make the nozzle to use, okay, I'm going to do it, you also have to lock these two, ok Ah , and now that is going to be the output of the injector nozzle, you know, pulling a wire from here and another of these two from here is what is going to be a joke, beauty, and The nozzle connector, guys, For you it is very easy to find, just take it and put it, you know, a connector and the indicator of the CG 150 and 160, right, 150 with electronic injection so that it is perfect, so. here I'm just going to cut it and make the mother-in-law And then I'm going to do the welding here guys, I can put it like this or I can also reverse it What's up What's up What's up What's up Hello guys Ready Well, now let's do the cleaning, right, as I promised , And then they took out the relezin, right, it's already working Hello, will the injector nozzle work and will I put Pontinha in the socket?

Remembering that before doing this? internal cleaning they do an external cleaning, look at the filter, no, now I'm going to put it here to see if it really works, guys, remove it here, hey guys, spraying without having anything. injecting at the end of the nozzle cleaning in the nozzle cleaning machine with kerosene inside and in the professional machine so you can see the center, some I am teaching you how to do this here, it is because this mechanism yes, this small one. advice without it also to sell factory ready on MercadoLivre if you are going to do it if you are going to save a lot, oh, it's running out, oh, it's done, oh, and it's working, guys, if you think it doesn't work, then, and After leaving it like that for five minutes, you can just remove it and you're done.

So, the injector nozzle cleaning is done, beauty, but there's something cooler I'm going to do now. , using the auto 80 here, beauty, you can even test the pressure of the nozzle and the feet, see if it was working, and also do the cleaning, beauty, to do this other test, very simple guys, let's get a syringe. alone and 3ml or 5ml maximum, it fits here in the injector nozzle, right, it fits in the straw that goes inside the auto80, then just take the auto 80 and connect it here, oh and the animals Zinho, great, if I want to know if the nozzle was hitting them.

You can inject, it's a little bit here at 80, we had it, oh, there's already pressure in here guys, and as you can see, of course, I didn't put anything in, Joe, okay, now let's go. to connect the tip, you'll see that it's going to release a And then, hello, I'm pressing here, it's going to inject, oh, and it's also going to release the car inside, oh, and then, oh, and the holes are all very clean , here I am doing a demonstration, but there is no need, and you, to waste beauty products G1 E So tell me how it works And then you can think about it and also about the flow rate of the ejector nozzle What's up What's up What's up Ah guys, very much more than ready, cleaning the injector nozzle and just reminding you if you don't have a 12 volt or 24 volt source similar to this one here or the 24 volt one works just as great, I always use this one, it always worked, it always worked So, if not you have none of these sources, you can use the battery charger, there is a place to disconnect.

Hello. It's the little guy that connects it to the battery charger, right, on a motorcycle or car, it can be 12 or 24 volts depending on what you're going to use it for and if you don't have any of that. You can connect it directly to the motorcycle battery, it works the same, another question from guys, if it works with a larger source, it also works, if here it is much larger, it has more amps, it has nothing to do with it. being 12 volts, oh, oh, and also a much larger relay works the same way, oh five feathers too, right?

And then the same thing, cool Ah, so here you go guys, click on the video, yo. I hope I have helped you with this advice, leave a thumbs up and activate the notification bell with a hug from Cleudo and until next time