Samsung 55 inch Smart TV has sound but no picture. Samsung model Un55h6203AF Television repair.

Do it one at a time if you want, I'll push them all out so they all fall out, oh God. Okay, these are all my new strips. I bought Shopjimmy and it's actually 10 pieces. These are two trips, okay and one, no big deal, and we also have for the end, when they connect, which are also different, okay, so I can. Not to confuse you at all, so we have the piece where our V-plus cable goes, where our line comes in, just trim that, push that back into the new one, okay, get rid of these, I'm actually going to save them because obviously they're still good, you never know how much someone might give me a tp or something, I'm going to go to the other one, okay, so I've got that, there we go, we'll make sure the holes line up, uh, I've got that. something is missing I don't know what happened when they fell on the floor there is one on the floor right here, things work again, that's it, it's fine and as you can see, the connectors are different, that is the old connector, the metal one, and this one it's the new connector for the newer strips, okay, and just do it all the way. down for the five if they're loose at the end just take a screwdriver and pry them open like I just did so they really stick there because remember we had to squeeze them to get them out so it's just plastic so there we go , okay, put all my strips in there, take all my lashes, four pins.

I'll hold it up as you'll call them, in fact, I get some duct tape, some packing tape, make sure you don't cover the lens, it might be too thick. I see, oh, foreigner, oh, so, okay, make sure it's going to be a little complicated here. I want to make sure it's in the notches at the top, make sure it's inside the notches and don't squeeze these controller tabs on the side. Okay, make sure that notches on all four corners looks good looks good excellent excellent excellent so we're going to mount our controller boards back to the bottom of the TV, remove the tape, be very careful, remove it and make sure that again be in that notch, okay? make sure the screen doesn't overlap or protrude from these brackets, everything looks good, it looks good, it should be pretty easy to put it back in here.

I'm going to go up to these, put it here smaller up and down, okay? In one of these two notches, put it there at the same time, simultaneously up, we go and we go down, that's it guys, and if you want, you can just plug in your cabinet. Do that, if I can, I'll connect my t. -With the board back on my controller boards, here we go, so I don't have to do that once I put the outer bezel on, that will already be done and there is a line, as you can see on the ribbon connector, to tell you how do it. everything is great, great, triple check again, make sure everything is flush, man, I'm actually still connecting.

I'm going to go ahead and turn it on just to make sure I didn't do it right. You never know. Make sure the screen is fine. It's not cracked, it looks good, it just appeared and don't worry about the stains from the suction cups that will eventually disappear. Okay, now our outer bezel probably wants to start with the bottom. Well, actually it should fit well quite easily. don't use excessive pores to push this in there it's okay just take your time that part fell into place and put it here we go guys it's that easy this is fine and obviously all I have to do now is go back to connect my LDB.

Plug the cable back into my main board and I should be able to check the image making sure I don't mess up any of those sliding tabs I think, I think, so what's going on? Okay, let's plug it in, put in the taillights. come on, turn the lights back on and there we go av at the bottom, so good, so far it looks good, okay, no lines, no shaking, no half slow motion movie because that's actually what happens if you do this and you get a slow motion image. one side or it's darker on one side or yeah, you'll probably damage one of the tabs or a lot of times this is easier, sometimes people put these connectors back in a little bit crooked or a little bit like a little bit bigger size. not completely there and your controller boards or your t-con board or even this connector here could be off, but yeah, that's what usually happens if one of those connectors is off;

So far, everything looks good, so let's leave the rest of the Put the TV back together, so, okay, put it back together, go ahead and plug it in. The flashing light should appear within a minute. Voila, okay guys, looks like we're ready to go. Thanks everyone for watching, be sure to subscribe. for more videos give me a like if you liked the video and until then I will see you in the next big dog.