YTread Logo
YTread Logo

How to Apply CarPro DLux Ceramic Coating to New Rims

May 29, 2021
Hello, what is happening youtubers? Your brand methods. Thanks for stopping by the channel. I'm very excited today. I have six new tires. I haven't had new tires since I was 17, so this is really exciting for me and us. I'm going to

apply

some Car Pro Deluxe Ceramic Coating since it's oil-free, but it should be pretty easy to clean. I'll check it out with Draft Car Pro, so the plan is to have six tires, so when I go out drifting, I can actually change my rear wheels once I've burned the first set and that way I can get home and dry off. the car back and forth, which is going to be amazing, so let's start unpacking them and

apply

ing some

ceramic

coating

at the moment of Truth, before we cover the rim with the car pro deluxe or antsy quartz

ceramic

coating

, let's go to apply car pro racer just to make sure any oil or anything and dust is removed from the rim, even though it is new.
how to apply carpro dlux ceramic coating to new rims
I want to make sure I have a good surface to deal with, so we're just going to spray a little bit, let's rub it, rub it now that we've cleaned the edge and we've prepped it, let's take the C wires out of the side of the deluxe box of Sea Courts, we'll find a block of foam to use with our four suede microfiber applicators, a 30 milliliter bottle of the actual ceramic coating, and a couple of stickers. it goes on the inside of the glass, you can't see it from the other side, but yes, you get 30 milliliters, it's actually quite a bit better material.
how to apply carpro dlux ceramic coating to new rims

More Interesting Facts About,

how to apply carpro dlux ceramic coating to new rims...

The professional pad and the cloth that they give you with it and just wrap this around the block now that you have it. little slots on the sides where you can take a credit card and insert it, so I'm going to do that, so now the idea is you want to put a few drops on this and you'll see the code flash. the surface and then you want to knock it down with a cloth, a microfiber, you want to use this in a well-ventilated area, it smells pretty bad and off-gassing now, in this case, where I'm using it on a matte surface. this will intensify the depth of the color and you can see that as I go over some of these surfaces and it will stay like this as well, we'll just take a microfiber and knock it down a little bit. try to avoid letting your skin touch the actual surface you have coated now you can apply several coats of this if you want it's not necessary it's a personal preference those blocks don't really reach the small areas so I'm going to take one of the extra cloths and then use my finger to poke around.
how to apply carpro dlux ceramic coating to new rims
I was expecting this to flash a little faster. It seems to take quite a long time to work. It's pretty much what I'm used to with older ceramic tiles. they came on and then immediately had to be polished and knocked down so they didn't have high spots and things like that. This is a pretty interesting product. I hope it lasts a while, so this is the first wheel I've made. To do the same process on the other wheels, everything seems to have turned out pretty well. You can also continue applying additional coats. If you want to do three fancy layers, go ahead.
how to apply carpro dlux ceramic coating to new rims
I'm going to go ahead and give each of them a single coat and see how much material I have left after in this 30 ml bottle. It doesn't seem like I used much on the single wheel, but I was pretty sparing because I wasn't sure how much I'm going to use. are you using that's it now this is a matte finish rim it will take about 24 hours to cure you want to keep it from getting wet during that time you want it to dry and cure and store it in a safe place guys so now we have all the coated

rims

and fancy ceramic, it's a really cool product to work with.
They don't pay me to tell you, but I have worked with other ceramic coatings like opti coat like the original. The formula is not the current one, but it has a very short evaporation time and you have to clean it quickly, but this was very easy to work with, but the finish you see is what you get, so don't forget to do those tangents. after 10 minutes of applying it, otherwise it is very difficult to remove the ceramic coating, especially when it is very thick in different areas, so all that is left is to mount and balance these tires.
I already have the tires mounted and balanced, so it's mounted. Get up and see how they look. One of the big things I had a problem with was that I forgot to order a hub-centered ring, so I tried to 3D print them just to see if I could. I used PLA, this material shrinks a bit so it's also not the right size, you really want to use something like ABS or nylon, something that can withstand heat a little better than this, so don't forget to order some rings centered on the hub, these are aluminum, they are for circuit racing.
I will put a link in the description definitely high quality, they fit quite well. I'll let you know if I have any vibrations or problems with them and we'll put the koenig decagrams 17 by 9 5 by 100 with a 73. one hole, that's why you need the rings centered on the hub because you have to adapt them and you don't really want to center them because you put a lot more tension on the bolts and you can experience vibrations whenever we have the rear. in the air, so we're just going to take off both tires and move to the front.
We have coated all wheels with ceramic. We have the tires mounted and balanced. Just one thing to let you know. I'm going to post a photo, so what happened was I got a little bit of drip edge on the cylinder and I missed it. Some, like I said, any finish you see on the wheel is obtained with the ceramic coating, so be sure to come back. and it looks exactly how you want it, don't leave the access on, make sure you do the tangent wipes, it will leave a movie that you won't see well, so if this video helped you guys, comment, subscribe and me.
I'll see you guys next time.

If you have any copyright issue, please Contact