YTread Logo
YTread Logo

3034D, 655D, 1534D Instructional Video English Brother Canada

Jun 06, 2021
Thank you for purchasing the Brother overlock machine on this DVD. We will start by explaining the characteristics of your machine. The machine is connected to a foot pedal that plugs into the outlet. Step on the pedal to start sewing by sliding the front cover to the right. Reveals a storage compartment for small sewing items You can remove the bed extension to sew tubular pieces with your free arm Attach the optional trim trap for a convenient way to catch trimmed fabric To attach the trim trap Insert it fully with both marks on the trim trap and the machine aligned the trim trap can also be used to store the pedal after use below we will show you how to prepare for threading always turn off the machine before threading lift the thread tree completely and load the thread spools use the presser foot lift lever to raise the presser foot turn the handwheel towards you to align the marks once the needle is fully raised the machine is ready to thread next we will show you how to thread the machine this example is for a two needle needle for threading from right to left seen from the front these spools are for the lower looper the upper looper the right needle and the left needle for safety always turn off the machine before threading then open the front cover to thread the lower looper pass the tree thread through the thread holder from the back of the thread plate to the front and through the number three hole after passing this thread through the blue tensioning disc pass it through each threading point numbered in blue one after another consecutively up to eight then slide the lower looper threading lever nine to the right to remove the lower looper to the right, pass the thread around and through the eye of the lower looper, pass the thread behind the upper looper, fold it with your left hand and turn the steering wheel once.
3034d 655d 1534d instructional video english brother canada
Now thread the top looper in the same way. way after passing a thread through the green tension disc pass it through each green numbered threading point one after another consecutively up to seven after passing the thread through the eye of the upper looper hold it towards the left thread the right needle Just as the looper did, he passes the thread through the pink tensioning disc and through each threading point numbered in pink one after another consecutively and then to the right of the separator after passing the thread through the thread guide of the needle bar pass it through the eye of the right needle read the left needle just as you did with the looper pass the thread through the yellow tensioning disc and through each threading point numbered in yellow one after another consecutively and then to the left of the separator after Press the thread through the thread guide of the needle bar and pass it through the eye of the left needle you have finished threading for a two-needle to adjust the thread.
3034d 655d 1534d instructional video english brother canada

More Interesting Facts About,

3034d 655d 1534d instructional video english brother canada...

Next, we will show you how to adjust the stitch to adjust the upper thread tension. Use the tension adjustment dial from right to left. The dials are for lower looper upper looper right needle and left needle the dials can usually be set to four, but you can use a lower value for lighter tension or a higher value for higher tension the stitch length is usually can be set to three so you can set the stitch length adjust the dial to a lower value for shorter stitches or a higher value for longer stitches, the stitch width can usually be set to five, but you can set the stitch width dial to a higher value for wider stitches or a lower value for narrower stitches to adjust the presser foot. pressure use the pressure adjustment screw of the presser foot, generally it can be set to turn the screw counterclockwise to reduce the foot pressure or clockwise to increase it.
3034d 655d 1534d instructional video english brother canada
There are two differential feeding teeth at the front and rear of the machine. The feed amount of each can be adjusted to match your particular fabric for neater seams, the differential feed can usually be set to 1.04 for fabrics that tend to wrinkle during sewing, set it between 0.7 and 1.0 and for fabrics that tend to stretch during sewing, set it between one zero point and two zero points. now let's try a test sew, turn on the machine and raise the presser foot holding the four threads in your left hand, pull the threads about 15 centimeters behind the presser foot, load the fabric and lower the presser foot, turn the handwheel towards you a few times and make sure the stitches are sewn pull the fabric to guide it and step on the pedal to start sewing after sewing for a while check the stitches to make sure they are even if the stitches are not neat try adjusting the stitches as described above Stop for about five centimeters beyond the end point, stop the machine and cut the thread with scissors.
3034d 655d 1534d instructional video english brother canada
Now let's try a real sewing session. Turn on the machine. Lower the presser foot and depress the pedal without sewing the fabric. Make a chain about two inches long. Raise the presser foot and load the fabric aligned with the presser foot guide, guide the fabric with your hands and use the pedal to adjust the speed. Let's look at how to secure the chains to prevent them from fraying after attaching the fabric. Run the machine without sewing to make a chain about two inches long, pull the chain in front of and under the presser foot, hold the chain and sew a few stitches, cut the excess chain with a knife at the end of the scene, so that a stitch leaves the edge of the fabric and stops the machine. the presser foot and raise the needle and then turn the fabric over turn the handwheel towards you to lower the needle to the same position at the end of the scene lower the presser foot and start sewing finally cut the excess thread with scissors in addition to securing Chaining in this way can hide the chain thread and tie it.
You can use a hand sewing needle with a large eye in the stitch. Another method is to apply a drop of fabric glue at the end of the stitch, after it dries, cut off the excess thread. Now let's look at other stitches and sewing techniques for a one-needle, three-thread setup. Remove the right or left needle. Always turn off the machine before removing needles. Turn the handwheel towards you to raise the needle and hold the needle in your left hand. use the included hex screwdriver to remove it before sewing a rolled hem stitch remove the left needle and sewing finger to remove the sewing finger open the front cover and pull the sewing finger to the right store the sewing finger in the front cover compartment to store it in a safe place if you will do it without cutting the edge of the fabric retract the blade with the blade lever on the front cover here we will show you how to replace the thread cut the thread on the thread spool load the new spool and tie the new thread lift the presser foot and turn the handwheel to lower the needle under these conditions pull the thread to the knot position when the knot reaches the tip of the needle cut the thread with scissors lift the needle and thread the needle eye you can also replace the upper looper and lower looper thread in the same way by pulling the thread next we will cover machine maintenance always turn off the machine before maintenance be sure to turn the handwheel to lower the needle open the front cover and use the included cleaning brush to clean the machine we recommend regular maintenance to ensure smooth and quiet operation of the machine oil the upper and lower looper regularly let's take a look at the sewing techniques available with the optional feet turn off Always turn the machine before replacing the feet raise the presser foot and push the foot holder button to remove the presser foot with the replacement foot aligned with the foot holder pin lower the presser foot lever and attach the presser foot use the blind stitch foot when blind sewing t-shirt sleeves, sweatpants cuffs or other stretch fabric to make shirring Attach the shirring foot and adjust the differential feed with the bead sequence foot you can sew beads, pearls and other decorations on collars or skirt hems the piping foot allows you to sew piping between two layers of fabric this option is useful for decorative embellishments on bags or cushions and with the ribbon foot you can cut the edge of the fabric while sewing elastic ribbon which is useful for sweaters, aprons and other pieces.
We hope you enjoy sewing your own pieces on your

brother

overlock machine. Oh

If you have any copyright issue, please Contact